Flexcharge NCHC3660 36 Volt 60 Amp Solar and Wind Charge Controller

Description

Flexcharge NCHC3660 | 36 Volt 60 Amp Solar and Wind Charge Controller
Flexcharge
Ultra High Efficiency 36V 60A Solar and Wind
Charging System Controller
Model: NCHC-36-60
US Manufactured Long Service Life and Performance History
We are a stocking Flexcharge dealer listed here on SES Flexcharge's dealer page.
The following is copyrighted by SES Flexcharge.
The patented circuit architecture developed during the design of the NC25A charge controller was used as the basis for the development of the NCHC family of controllers. Pretty it may not be, but the NCHC will regulate PV, Wind, or any other current limited charging source with the highest efficiency possible in an alternative energy system charge controller.
For Lead Acid GEL, AGM, and Flooded cell Batteries. Also works with wet cell NiCad batteries.  Do not use on Lithium batteries of any type.
Efficiency
How does the NCHC achieve this level of efficiency, and why is it so important? We designed the NCHC controllers with an amazingly low insertion loss resistance of only 0.001 ohms. ( Insertion Loss Resistance is the total resistance of the controllers regulating circuit from input to output on both the positive and negative wires).
Now a little math to prove the point (That' s what happens when you let the engineers work on a web page...)
The power wasted as heat in a charge controller is calculated by the following simple formula:
(Power Wasted as Heat) = (Resistance) x (Charging Current) x (Charging Current) or P= R x I2.
So how much power does the NCHC 60 ampere controller waste at 60A of charging current?
P = 0.001 x 60 x 60 = Only 3.6 watts.
By Comparison how much power does a typical brand 60A controller with 0.010 ohms of insertion loss resistance waste while charging at 60 amperes.
P= 0.01 x 60 x 60 = 36 watts of heat (WOW!) Precisely why you will see large heat sinks on these controllers, to dissipate all that wasted energy. You would also need an additional 36W solar panel ($$$) to put the same amount of energy into the battery bank, than is required with the NCHC-60 controller.
Expandable
The NCHC controllers can be expanded with amazing simplicity to grow with your charging system. Just add an additional high efficiency contactor and extend three wires from the previous contactor. It is possible to add as many as 4ea 100A contactors to the standard NCHC, with no special modifications, or as many as 20ea with a simple addition of an interface contactor. That's as much as 2000A of charging current capacity at up to 48V (96KWs of Charging Energy) while still using only 0.005 amperes to operate the charging circuitry.
By using separate contactors for different types of charging sources the charging sources are automatically isolated from each other when the controller is regulating. For example: Connect the PV System to one contactor, connect a wind generator to the other contactor which is paired with a divert contactor. When the controller goes to Divert mode the PV system is isolated from the Wind system and the divert load is applied to the wind generator only.
Charge Divert
By adding a different type of contactor you can add Charge Divert to the NCHC. This feature connects the charging source directly, with no regulation, to the Divert Load. Divert is active only while voltage and current are at usable levels from the charging source.
Some uses for Charge Divert:
Pumping applications
Ventilation Blowers
Loads on wind and water permanent magnet generators.
Features
5 YEAR WARRANTY
AUTO ASSEMBLED IN THE USA TO ISO9000 SPECIFICATIONS.
BETTER THAN 99.50% CHARGING EFFICIENCY FROM 1A OF CHARGING CURRENT.
OPERATES EFFICIENTLY (98%) ON SYSTEMS SIZES AS LOW AS 0.25A OF CHARGING INPUT.
CHARGES BATTERIES FROM 0 VOLTS WITH FULL UNINTERRUPTED POWER.
HIGH AMPERAGE CHARGE CAPACITY, 24V, 36, AND 48V MODELS WITH UP TO 200A CAPACITIES).
UP TO 200 AMP CHARGE DIVERT, OPTIONAL.
STABLE DIVERT CIRCUITRY PREVENTS DROPOUTS IF CHARGE SOURCE VOLTAGE FALLS TOO LOW.
DIVERTS ONLY WHEN VOLTAGE AND CURRENT ARE AT USABLE LEVELS. PERFECT FOR MOTOR TYPE LOADS (FANS, PUMPS, etc...)
PEAK CHARGE VOLTAGE ADJUSTMENT
ACCURATELY CHARGES THROUGH BATTERY ISOLATORS, AND WORKS PERFECTLY WITH COMBINERS. CAN BE USED AS A BATTERY COMBINER. CALL Flexcharge USA FOR INSTRUCTIONS.
CONSUMES ONLY 4mA (0.004A) WHILE CHARGING AND AT NIGHT, 2mA IF YOU DO NOT USE THE CHARGE INDICATOR
CHARGES BATTERIES AT FULL POWER, BELOW THE PLATE SATURATION POINT, TO CHARGE BATTERIES FASTER, AND REDUCE ELECTROLYTE DEPLETION BY UP TO 90% OVER CONVENTIONAL CONSTANT VOLTAGE, PWM, & HIGH FREQUENCY CHARGE REGULATORS
BATTERIES START CHARGING AT 0.005A OF CHARGE CURRENT AND CAN HANDLE INTERMITTENT SURGES UP TO 300A
CONTROLLER CAN WITHSTAND OPEN CIRCUIT INPUT VOLTAGES SPIKES OF 500V AND 100 VOLTS CONTINUOUS WITHOUT DAMAGE
REVERSE POLARITY, AND TRANSIENT VOLTAGE PROTECTION ON THE BATTERY SENSE WIRES.
NO POWER WASTING SAMPLE PERIODS.
REMOTE BATTERY VOLTAGE SENSING SO THE CONTROLLER CAN BE MOUNTED ANYWHERE BETWEEN THE CHARGING SOURCE AND THE BATTERIES
EASY TO INSTALL USING THE LABELED CORROSION RESISTANT NICKLE/BRASS/STAINLESS STEEL CONNECTOR, AND CONTACTOR TERMINALS
U/L 94V-O RATED ENCLOSURE.
COMPLETELY SEALED ELECTRONICS FOR MARINE OR OUTDOOR MOUNTING.
NCHC General Specifications
Flexcharge NCHC
Min
Max
Min
Max
Min
Max
Min
Max
Model Number
NCHC-12V
NCHC-24V
NCHC-36V
NCHC-48V
Input Voltage Transients
-
2000V
-
2000V
-
2000V
-
2000V
Input Voltage Continuous
0V
100V
0V
100V
0V
100V
0V
100V
Operating Current (Charging & Standby)
2 mA
5 mA
2 mA
5 mA
2 mA
5 mA
2 mA
5 mA
System Size Limits
0.05A
Contactor  Rating
0.05A
Contactor  Rating
0.05A
Contactor Rating
0.05A
Contactor Rating
Total Efficiency
98.9%
99.90%
98.9%
99.92%
98.9%
99.96%
98.9%
99.98%
Insertion Loss Resistance (Ohms)
0.0005
0.002
0.0005
0.002
0.0005
0.002
0.0005
0.002
Divert Current Capacity
-
Contactor Rating
-
Contactor Rating
-
Contactor Rating
-
Contactor Rating
Operating Temp.
-20°C
+60°C
-20°C
+60°C
-20°C
+60°C
-20°C
+60°C
Storage Temp.
-40°C
+70°C
-40°C
+70°C
-40°C
+70°C
-40°C
+70°C
Dimensions
9"W x 4 1/2"H x 2 3/8"D
NOTE:
All NCHC controllers must be mounted vertically
Hurricane Wind Power
Build News Magazine
Best Off Grid
2016
Product Supplier
Renewable Energy
UP TO 50% DISCOUNTS
TOP BRANDS
Payment
Shipping
Returns
Payment
Shipping
Returns
We accept payment by any of the following methods:
PayPal
Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner!
We offer
Fast shipping
on all orders!
Your order will be dispatched within 1-3 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class).
In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement.
If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not.
You can return a product for up to 14 days from the date you purchased it.
Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt.
See our other items
Thank you for visiting our Ebay store!
Flexcharge Ultra High Efficiency 36V 60A Solar and Wind Charging System Controller Model: NCHC-36-60 US Manufactured Long Service Life and Performance History We are a stocking Flexcharge dealer listed here on SES Flexcharge's dealer page: [http://www.flexcharge.com/Where-to-buy.html] (http://www.flexcharge.com/Where-to-buy.html) The following is copyrighted by SES Flexcharge. The patented circuit architecture developed during the design of the NC25A charge controller was used as the basis for the development of the NCHC family of controllers. Pretty it may not be, but the NCHC will regulate PV, Wind, or any other current limited charging source with the highest efficiency possible in an alternative energy system charge controller. For Lead Acid GEL, AGM, and Flooded cell Batteries. Also works with wet cell NiCad batteries. Do not use on Lithium batteries of any type. Efficiency How does the NCHC achieve this level of efficiency, and why is it so important? We designed the NCHC controllers with an amazingly low insertion loss resistance of only 0.001 ohms. ( Insertion Loss Resistance is the total resistance of the controllers regulating circuit from input to output on both the positive and negative wires). Now a little math to prove the point (That' s what happens when you let the engineers work on a web page...) The power wasted as heat in a charge controller is calculated by the following simple formula: (Power Wasted as Heat) = (Resistance) x (Charging Current) x (Charging Current) or P= R x I2. So how much power does the NCHC 60 ampere controller waste at 60A of charging current? P = 0.001 x 60 x 60 = Only 3.6 watts. By Comparison how much power does a typical brand 60A controller with 0.010 ohms of insertion loss resistance waste while charging at 60 amperes. P= 0.01 x 60 x 60 = 36 watts of heat (WOW!) Precisely why you will see large heat sinks on these controllers, to dissipate all that wasted energy. You would also need an additional 36W solar panel ($$$) to put the same amount of energy into the battery bank, than is required with the NCHC-60 controller. Expandable The NCHC controllers can be expanded with amazing simplicity to grow with your charging system. Just add an additional high efficiency contactor and extend three wires from the previous contactor. It is possible to add as many as 4ea 100A contactors to the standard NCHC, with no special modifications, or as many as 20ea with a simple addition of an interface contactor. That's as much as 2000A of charging current capacity at up to 48V (96KWs of Charging Energy) while still using only 0.005 amperes to operate the charging circuitry. By using separate contactors for different types of charging sources the charging sources are automatically isolated from each other when the controller is regulating. For example: Connect the PV System to one contactor, connect a wind generator to the other contactor which is paired with a divert contactor. When the controller goes to Divert mode the PV system is isolated from the Wind system and the divert load is applied to the wind generator only. Charge Divert By adding a different type of contactor you can add Charge Divert to the NCHC. This feature connects the charging source directly, with no regulation, to the Divert Load. Divert is active only while voltage and current are at usable levels from the charging source. Some uses for Charge Divert: ---Pumping applications ---Ventilation Blowers ---Loads on wind and water permanent magnet generators. Features ---5 YEAR WARRANTY ---AUTO ASSEMBLED IN THE USA TO ISO9000 SPECIFICATIONS. ---BETTER THAN 99.50% CHARGING EFFICIENCY FROM 1A OF CHARGING CURRENT. ---OPERATES EFFICIENTLY (98%) ON SYSTEMS SIZES AS LOW AS 0.25A OF CHARGING INPUT. ---CHARGES BATTERIES FROM 0 VOLTS WITH FULL UNINTERRUPTED POWER. ---HIGH AMPERAGE CHARGE CAPACITY, 24V, 36, AND 48V MODELS WITH UP TO 200A CAPACITIES). ---UP TO 200 AMP CHARGE DIVERT, OPTIONAL. ---STABLE DIVERT CIRCUITRY PREVENTS DROPOUTS IF CHARGE SOURCE VOLTAGE FALLS TOO LOW. ---DIVERTS ONLY WHEN VOLTAGE AND CURRENT ARE AT USABLE LEVELS. PERFECT FOR MOTOR TYPE LOADS (FANS, PUMPS, etc...) ---PEAK CHARGE VOLTAGE ADJUSTMENT ---ACCURATELY CHARGES THROUGH BATTERY ISOLATORS, AND WORKS PERFECTLY WITH COMBINERS. CAN BE USED AS A BATTERY COMBINER. CALL Flexcharge USA FOR INSTRUCTIONS. ---CONSUMES ONLY 4mA (0.004A) WHILE CHARGING AND AT NIGHT, 2mA IF YOU DO NOT USE THE CHARGE INDICATOR ---CHARGES BATTERIES AT FULL POWER, BELOW THE PLATE SATURATION POINT, TO CHARGE BATTERIES FASTER, AND REDUCE ELECTROLYTE DEPLETION BY UP TO 90% OVER CONVENTIONAL CONSTANT VOLTAGE, PWM, & HIGH FREQUENCY CHARGE REGULATORS ---BATTERIES START CHARGING AT 0.005A OF CHARGE CURRENT AND CAN HANDLE INTERMITTENT SURGES UP TO 300A ---CONTROLLER CAN WITHSTAND OPEN CIRCUIT INPUT VOLTAGES SPIKES OF 500V AND 100 VOLTS CONTINUOUS WITHOUT DAMAGE ---REVERSE POLARITY, AND TRANSIENT VOLTAGE PROTECTION ON THE BATTERY SENSE WIRES. ---NO POWER WASTING SAMPLE PERIODS. ---REMOTE BATTERY VOLTAGE SENSING SO THE CONTROLLER CAN BE MOUNTED ANYWHERE BETWEEN THE CHARGING SOURCE AND THE BATTERIES ---EASY TO INSTALL USING THE LABELED CORROSION RESISTANT NICKLE/BRASS/STAINLESS STEEL CONNECTOR, AND CONTACTOR TERMINALS ---U/L 94V-O RATED ENCLOSURE. ---COMPLETELY SEALED ELECTRONICS FOR MARINE OR OUTDOOR MOUNTING. NCHC General Specifications Flexcharge NCHC Min Max Min Max Min Max Min Max Model Number NCHC-12V NCHC-24V NCHC-36V NCHC-48V Input Voltage Transients - 2000V - 2000V - 2000V - 2000V Input Voltage Continuous 0V 100V 0V 100V 0V 100V 0V 100V Operating Current (Charging & Standby) 2 mA 5 mA 2 mA 5 mA 2 mA 5 mA 2 mA 5 mA System Size Limits 0.05A Contactor Rating 0.05A Contactor Rating 0.05A Contactor Rating 0.05A Contactor Rating Total Efficiency 98.9% 99.90% 98.9% 99.92% 98.9% 99.96% 98.9% 99.98% Insertion Loss Resistance (Ohms) 0.0005 0.002 0.0005 0.002 0.0005 0.002 0.0005 0.002 Divert Current Capacity - Contactor Rating - Contactor Rating - Contactor Rating - Contactor Rating Operating Temp. -20°C +60°C -20°C +60°C -20°C +60°C -20°C +60°C Storage Temp. -40°C +70°C -40°C +70°C -40°C +70°C -40°C +70°C Dimensions 9"W x 4 1/2"H x 2 3/8"D NOTE: All NCHC controllers must be mounted vertically [FREE! Sellers: Add a FREE map to your listings. FREE!] (http://newage.mystoremaps.com/echo/tagLine?sid=cea073c8-fc6f-494f-9ca5-610e8850a127&tid=2) Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application
Flexcharge NCHC3660 | 36 Volt 60 Amp Solar and Wind Charge Controller
Flexcharge
Ultra High Efficiency 36V 60A Solar and Wind
Charging System Controller
Model: NCHC-36-60
US Manufactured Long Service Life and Performance History
We are a stocking Flexcharge dealer listed here on SES Flexcharge's dealer page:
http://www.flexcharge.com/Where-to-buy.html
The following is copyrighted by SES Flexcharge.
The patented circuit architecture developed during the design of the NC25A charge controller was used as the basis for the development of the NCHC family of controllers. Pretty it may not be, but the NCHC will regulate PV, Wind, or any other current limited charging source with the highest efficiency possible in an alternative energy system charge controller.
For Lead Acid GEL, AGM, and Flooded cell Batteries. Also works with wet cell NiCad batteries.  Do not use on Lithium batteries of any type.
Efficiency
How does the NCHC achieve this level of efficiency, and why is it so important? We designed the NCHC controllers with an amazingly low insertion loss resistance of only 0.001 ohms. ( Insertion Loss Resistance is the total resistance of the controllers regulating circuit from input to output on both the positive and negative wires).
Now a little math to prove the point (That' s what happens when you let the engineers work on a web page...)
The power wasted as heat in a charge controller is calculated by the following simple formula:
(Power Wasted as Heat) = (Resistance) x (Charging Current) x (Charging Current) or P= R x I2.
So how much power does the NCHC 60 ampere controller waste at 60A of charging current?
P = 0.001 x 60 x 60 = Only 3.6 watts.
By Comparison how much power does a typical brand 60A controller with 0.010 ohms of insertion loss resistance waste while charging at 60 amperes.
P= 0.01 x 60 x 60 = 36 watts of heat (WOW!) Precisely why you will see large heat sinks on these controllers, to dissipate all that wasted energy. You would also need an additional 36W solar panel ($$$) to put the same amount of energy into the battery bank, than is required with the NCHC-60 controller.
Expandable
The NCHC controllers can be expanded with amazing simplicity to grow with your charging system. Just add an additional high efficiency contactor and extend three wires from the previous contactor. It is possible to add as many as 4ea 100A contactors to the standard NCHC, with no special modifications, or as many as 20ea with a simple addition of an interface contactor. That's as much as 2000A of charging current capacity at up to 48V (96KWs of Charging Energy) while still using only 0.005 amperes to operate the charging circuitry.
By using separate contactors for different types of charging sources the charging sources are automatically isolated from each other when the controller is regulating. For example: Connect the PV System to one contactor, connect a wind generator to the other contactor which is paired with a divert contactor. When the controller goes to Divert mode the PV system is isolated from the Wind system and the divert load is applied to the wind generator only.
Charge Divert
By adding a different type of contactor you can add Charge Divert to the NCHC. This feature connects the charging source directly, with no regulation, to the Divert Load. Divert is active only while voltage and current are at usable levels from the charging source.
Some uses for Charge Divert:
Pumping applications
Ventilation Blowers
Loads on wind and water permanent magnet generators.
Features
5 YEAR WARRANTY
AUTO ASSEMBLED IN THE USA TO ISO9000 SPECIFICATIONS.
BETTER THAN 99.50% CHARGING EFFICIENCY FROM 1A OF CHARGING CURRENT.
OPERATES EFFICIENTLY (98%) ON SYSTEMS SIZES AS LOW AS 0.25A OF CHARGING INPUT.
CHARGES BATTERIES FROM 0 VOLTS WITH FULL UNINTERRUPTED POWER.
HIGH AMPERAGE CHARGE CAPACITY, 24V, 36, AND 48V MODELS WITH UP TO 200A CAPACITIES).
UP TO 200 AMP CHARGE DIVERT, OPTIONAL.
STABLE DIVERT CIRCUITRY PREVENTS DROPOUTS IF CHARGE SOURCE VOLTAGE FALLS TOO LOW.
DIVERTS ONLY WHEN VOLTAGE AND CURRENT ARE AT USABLE LEVELS. PERFECT FOR MOTOR TYPE LOADS (FANS, PUMPS, etc...)
PEAK CHARGE VOLTAGE ADJUSTMENT
ACCURATELY CHARGES THROUGH BATTERY ISOLATORS, AND WORKS PERFECTLY WITH COMBINERS. CAN BE USED AS A BATTERY COMBINER. CALL Flexcharge USA FOR INSTRUCTIONS.
CONSUMES ONLY 4mA (0.004A) WHILE CHARGING AND AT NIGHT, 2mA IF YOU DO NOT USE THE CHARGE INDICATOR
CHARGES BATTERIES AT FULL POWER, BELOW THE PLATE SATURATION POINT, TO CHARGE BATTERIES FASTER, AND REDUCE ELECTROLYTE DEPLETION BY UP TO 90% OVER CONVENTIONAL CONSTANT VOLTAGE, PWM, & HIGH FREQUENCY CHARGE REGULATORS
BATTERIES START CHARGING AT 0.005A OF CHARGE CURRENT AND CAN HANDLE INTERMITTENT SURGES UP TO 300A
CONTROLLER CAN WITHSTAND OPEN CIRCUIT INPUT VOLTAGES SPIKES OF 500V AND 100 VOLTS CONTINUOUS WITHOUT DAMAGE
REVERSE POLARITY, AND TRANSIENT VOLTAGE PROTECTION ON THE BATTERY SENSE WIRES.
NO POWER WASTING SAMPLE PERIODS.
REMOTE BATTERY VOLTAGE SENSING SO THE CONTROLLER CAN BE MOUNTED ANYWHERE BETWEEN THE CHARGING SOURCE AND THE BATTERIES
EASY TO INSTALL USING THE LABELED CORROSION RESISTANT NICKLE/BRASS/STAINLESS STEEL CONNECTOR, AND CONTACTOR TERMINALS
U/L 94V-O RATED ENCLOSURE.
COMPLETELY SEALED ELECTRONICS FOR MARINE OR OUTDOOR MOUNTING.
NCHC General Specifications
Flexcharge NCHC
Min
Max
Min
Max
Min
Max
Min
Max
Model Number
NCHC-12V
NCHC-24V
NCHC-36V
NCHC-48V
Input Voltage Transients
-
2000V
-
2000V
-
2000V
-
2000V
Input Voltage Continuous
0V
100V
0V
100V
0V
100V
0V
100V
Operating Current (Charging & Standby)
2 mA
5 mA
2 mA
5 mA
2 mA
5 mA
2 mA
5 mA
System Size Limits
0.05A
Contactor  Rating
0.05A
Contactor  Rating
0.05A
Contactor Rating
0.05A
Contactor Rating
Total Efficiency
98.9%
99.90%
98.9%
99.92%
98.9%
99.96%
98.9%
99.98%
Insertion Loss Resistance (Ohms)
0.0005
0.002
0.0005
0.002
0.0005
0.002
0.0005
0.002
Divert Current Capacity
-
Contactor Rating
-
Contactor Rating
-
Contactor Rating
-
Contactor Rating
Operating Temp.
-20°C
+60°C
-20°C
+60°C
-20°C
+60°C
-20°C
+60°C
Storage Temp.
-40°C
+70°C
-40°C
+70°C
-40°C
+70°C
-40°C
+70°C
Dimensions
9"W x 4 1/2"H x 2 3/8"D
NOTE:
All NCHC controllers must be mounted vertically
FREE! Sellers: Add a FREE map to your listings. FREE!
Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application
Hurricane Wind Power
Build News Magazine
Best Off Grid
2016
Renewable Energy
Product Supplier
UP TO 50% DISCOUNTS
TOP BRANDS
See our other items
Payment
We accept payment by any of the following methods:
PayPal
Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner!
Shipping
We offer
Fast shipping
on all orders!
Your order will be dispatched within 1-3 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class).
In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement.
Returns
If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not.
You can return a product for up to 14 days from the date you purchased it.
Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt.
Thank you for visiting our Ebay store!